Swing Out Spare Tire Carrier Kit

AEV Spare Tyre Carrier Installation - YouTube
Installation of AEV Spare Tyre Carrier onto a 2007 JK Jeep Wrangler. ... View Video

Installation Guide For The JK RockGuard Spare Tire ...
The carrier several times as you finalize the installa-tion. The tire mount is set for 5 on 5 lug pattern for the stock JK wheels. Wheel adapters are available from TeraFlex for other wheel lug patterns. Adjust the wheel mount so the tire pushes gently against the tubes of the tire carrier as you tighten the spare tire lug nuts. ... Retrieve Doc

Rocky Mountain Westy Swing Away Carrier Kit Installation ...
The Swing Away Carrier Kit allows you to carry a larger diameter spare tire that otherwise would not fit within the stock clamshell spare tire carrier at the front of the van. Our stand alone design mounts to the van’s body allowing you to retain your stock bumpers. Page 1 Rocky Mountain Westy - Ph. (970) 310-3441 ... Doc Retrieval

HMMWV Drop Down Spare Tire Carrier Accessory Kit
To Swing Closed the Drop Down Spare Tire Carrier Assembly (Refer to Figure 5-1) 1. Ensure the spare tire carrier is in its fully-raised position, or that it’s high enough to clear the Bumper Lock (6) shown in Figure 5-1. 2. If the spare tire carrier is in the locked-open position, unlock it by pushing up on the Stop Latch (3). 3. ... Doc Retrieval

Rear Bumper Replacement W/ Tire Carrier - Go Industries
Bring the tire carrier swing arm towards the rear door plate and adjust the rear door plate as necessary until the tire carrier Mount the spare tire to the carrier using lug nuts from step #2 and tighten. Adjust the 3rd brake light assembly to a safe Rear Bumper Replacement W/ Tire ... Read Here

#255-40 SWING OUT TIRE SYSTEM INSTALLATION INSTRUCTIONS ...
The self-locking nut. The tighter you tighten the nut, the harder it is to swing out the tire carrier. Adjust to your preference. 6. Install the grease zerk, page 2, and grease. 7. Install tire mounting bracket to swing-away, as shown on pages 2 & 3. 8. Install spare tire to tire mount bracket, as shown on Page 3. ... Read Here

INSTALLATION INSTRUCTIONS INST-17-13-010C J Body-Mounted Tire ...
2. Remove the stock spare tire carrier if it is present. It is recommended that a Poison Spyder Tramp Stamp or Tramp Stamp II be installed in its place to clean up the appearance of the tailgate, however this is not necessary for installation of the tire carrier. 3. Use a 7mm nut driver to remove the license plate ... View Doc

Swing Arm Tire Carrier Heavy Duty (SWATCHD )
• Swing Arm Version installs in less than 20 minutes and requires a few 9/16” wrenches • Store / remove spare tire in seconds • Fulcrum styled Lift-assist design allows soldier to stow a standard HWWMV tire, using only 53 lbs of lift or only 43 lbs if using the Spinner Lift Assist Handle ... Fetch Doc

Honda Passport - Wikipedia
EX had the spare tire below the cargo area and LX mounted in a swing carrier at rear. Minor changes for the 2000 model year included 2-tone exterior colors, and optional 16 in (406 mm) wheels for the LX trim. ... Read Article

Jeep CJ - Wikipedia
It was a limited-production model that featured the V6 engine, front bucket seats and a rear bench, roll bar, heavy-duty frame and springs, a locking differential, oil-pan skid plate, rear swing-out tire carrier, full wheel covers, ammeter, and oil pressure gauges; padded visors were optional. ... Read Article

SWING-A-WAY TIRE/CAN CARRIER - CARiD.com
SWING-A-WAY TIRE CARRIER 1987-95 YJKits # 85095, 86095 Prepare to install kit 1. Remove spare tire. 2. Center stop lamp. a. Remove screw and cover from open tailgate. b. Disconnect center stop lamp wire connectors Pull the inner fender out from under rear quarter panel as shown. ... Access Document

Hitchgate™ Spare - WilcoOffroad.com | Tiregate Tire Carriers
Hitchgate™ Spare Tire Carrier Installation Guide . HITCHGATE 4/16/2007 BASIC Pull the latch pin and test the swing of the HitchGate. If it swings too easily, There are 2 different upper lug brackets included in your kit. (14mm and 12 mm) ... Access Doc

Installation Instructions Rear Tire Carrier - CARiD.com
Installation Instructions - Rear Tire Carrier Section 1 Remove Plastic Cover; Disconnect Light Connector; Remove Grommet; Cut Wire Page 5 Step 1 Tools Step 1 Step 3 Step 2 Step 2 Step 3 Open the tailgate. Slide a flat blade screwdriver Pry out the grommet on the outside of the tailgate. ... Fetch Full Source

HMMWV SPARE TIRE CARRIER - Ibis Tek
HMMWV SPARE TIRE CARRIER SIMPLE OPERATION Our TACOM-approved Spare Tire Carrier (STC) provides a simple, user-friendly design for raising and lowering a HMMWV tire. The STC is designed to swing away from the bumper and features a mechanical assist for controlled lowering. TACOM approved, NSN: 2590-01-525-1995 ... Get Document

JEEP TJ, YJ, & UNLIMITED (TJL) SWING-A-WAY TIRE CARRIER SWING ...
Swing-Away Tire Carrier & Tire/Can Carrier 2 Kits 85095, -201, 86095, -201 Prepare to install kit 1. Remove spare tire. 2. Center stop lamp. a. Remove screw and cover from open tailgate. ... Retrieve Doc

Bumper/Swing-out Tire Carrier - Wanderingtrail.com
Swing-out should swing with some ease. 5. Locate the cam lever and locking rod. 6. Open the swing-out and insert the locking rod. Then close the swing-out to keep the locking rod from falling out. 7. Slide the black washer over the locking rod and then the bellville washer (raised side up). 8. Now attach the cam lever using the 3/8”x 2” bolt. ... Retrieve Full Source

Product: Spare Tire License Plate Mount Part ... - 4x4 Media
Align the spare tire mounting studs with the holes in the provided mount that has the square holes in it. Attach this bracket to the spare tire studs with the provided 1/2" push nuts. A deep socket can be used to tap these on if necessary. Route the new light wiring through the hole in the spare tire carrier. ... Get Content Here

Installation Instructions Rear Tire Carrier Part Number 44943
Tire Carrier Swing Arm Assembly #508.54 Section 7 Attach Tire Carrier Swing Arm Assembly to Casting Step 1 Step 1 If your vehicle has a Modular Bumper with End Caps installed, you will first have to remove the knock-out disk in the right-side step pad before dropping the Tire Carrier Swing Arm assembly into the receiver. ... View Document

Excursion Rear Bumper - Suddenlink
Steel), and would incorporate a swing-away spare tire carrier as well as accommodating the license plate, receiver hitch, trailer electrical connector, and backup sensors. This was far easier said than done, but worth the effort — to me at least. This project started in April. Phase One was the construction of the bumper itself. That done, the ... Get Doc